HPFS Instruments India LLP

V’ Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V’ Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.

The 'V’ Block has a total three magnetic surfaces. Top and Bottom with 90 'V’ angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 2", 3", 4" & 6" 'V’ Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.

The permanent magnet holds the work firmly in the 'V’ and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

• Compound sine table, can be use to grind two way angle at same time.
• A positive locking device is mounted on the base.
• Made from high quality steel.
• Hardened and ground to 58 -62 Rc.
• An angle can be set to within ±5 seconds of degree.
• Firm hinge clamps reduce possibility of distortions.
• Tapped hole in Top, sides and end, facilities clamping.
• Suitable for 0-45 degree capacity

• CRYSTAL" Brand AA-603 Magnetic Sine Table is complete Sine System for precision grinding. ' Crystal' Sine table is supplied with Fine Pitch Permanent Magnetic Chuck.

  
  Features:
  

  • Magnetic Sine tables are ideal for precision angle grinding & inspections. 
  • They are made from high quality steel & base plate contains hardened bits. An angle can be set to within ± 5 seconds of a degree. 
  • Firm hinge clamps reduce possibility of distortions. 
  • Flatness 0.005mm per 100 mm. Center distance of the roller is within 0.005 min. Fine pitch chuck of 9.9mm with laminated brass pole is provided for rigid clamping of small , medium & large components.
  • Suitable for angle range from 0-45 degree.

Additional Information:

• Delivery Time: Ex-stock

V’ Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V’ Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.

The 'V’ Block has a total three magnetic surfaces. Top and Bottom with 90 'V’ angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 2", 3", 4" & 6" 'V’ Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.

The permanent magnet holds the work firmly in the 'V’ and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

'V’ Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V’ Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.

The 'V’ Block has a total three magnetic surfaces. Top and Bottom with 90 'V’ angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 2", 3", 4" & 6" 'V’ Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.

The permanent magnet holds the work firmly in the 'V’ and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

• Ground and finished on four sides.
• Precision ground in matched pairs.
• Variation in matched parallels is within 0.010 mm.
• Thickness, Width and length are nominal and within ¡Ó 0.1mm upto 200mmLength ¡Ó 0.2mm upto 450mm Length.
• Accuracy for Parallelism & Squareness is ¡Ó 0.005 mm upto 200mm Length and ¡Ó0.010mm upto 450mm Length.
• All the four sides are chamfered.

Standard AA – 1511 S:

• ‘Crystal ’ Magnetic Holder has instant grip at the turn of a handle. Incorporating Plain and Vee faces, it is equally effective in securing iron, steel sheets, bars or tubes, on machine bed or any other flat ferrous base. This can be used in Tool Room, Shop Floor, Inspection Department, Assembly Shop, and has unlimited application in Welding Shop.

Hardened AA -1511 H:

• Same as Cat.No.AA-1511 S but with hardened holding surface and ‘V’ angle. With this type, all ‘V’ angles are equipped with Hardened Steel Plates, which ensure extra resistance.

We are highly engaged in offering Magnetic Tool Holder to our prestigious clients.

• Designed to hold work magnetically for Inspection and Layout work, very useful for holding odd shaped parts for grinding, having large magnetic surface of 100×175 mm. precision ground.
• Accuracy for flatness, parallelism and squareness is within 0.005mm.
• Manufacturer of a wide range of products which include magnetic tool holder, magnetic holder, magnetic rectangular blocks and series